mirror of https://github.com/ropg/ezTime
Rop
7 years ago
parent
a2187f20c6
commit
4b1ffe5379
@ -0,0 +1,88 @@
|
||||
/*
|
||||
* Note: to use an ethernet shield, You must also set #define EZTIME_ETHERNET in $sketch_dir/libraries/ezTime/src/ezTime.h
|
||||
*
|
||||
* Also note that all ezTime examples can be used with an Ethernet shield if you just replace the beginning of the sketch
|
||||
* with the beginning of this one.
|
||||
*/
|
||||
|
||||
#include <ezTime.h>
|
||||
|
||||
#include <Ethernet.h>
|
||||
|
||||
// Enter a MAC address for your controller below. (Or use address below, just make sure it's unique on your network)
|
||||
// Newer Ethernet shields have a MAC address printed on a sticker on the shield
|
||||
#define MAC_ADDRESS { 0xBA, 0xDB, 0xAD, 0xC0, 0xFF, 0xEE }
|
||||
|
||||
void setup() {
|
||||
|
||||
// Open serial communications and wait for port to open:
|
||||
Serial.begin(115200);
|
||||
while (!Serial) { ; } // wait for serial port to connect. Needed for native USB port only
|
||||
Serial.println();
|
||||
|
||||
// You can use Ethernet.init(pin) to configure the CS pin
|
||||
//Ethernet.init(10); // Most Arduino shields (default if unspecified)
|
||||
//Ethernet.init(5); // MKR ETH shield
|
||||
//Ethernet.init(0); // Teensy 2.0
|
||||
//Ethernet.init(20); // Teensy++ 2.0
|
||||
//Ethernet.init(15); // ESP8266 with Adafruit Featherwing Ethernet
|
||||
//Ethernet.init(33); // ESP32 with Adafruit Featherwing Ethernet
|
||||
|
||||
Serial.print(F("Ethernet connection ... "));
|
||||
byte mac [] = MAC_ADDRESS;
|
||||
if (Ethernet.begin(mac) == 0) {
|
||||
Serial.println(F("failed. (Reset to retry.)"));
|
||||
while (true) { ; }; // Hang
|
||||
} else {
|
||||
Serial.print(F("got DHCP IP: "));
|
||||
Serial.println(Ethernet.localIP());
|
||||
}
|
||||
// give the Ethernet shield a second to initialize:
|
||||
delay(1000);
|
||||
|
||||
// OK, we're online... So the part above here is what you swap in before the waitForSync() in the other examples...
|
||||
|
||||
|
||||
// Wait for ezTime to get its time synchronized
|
||||
waitForSync();
|
||||
|
||||
Serial.println();
|
||||
Serial.println("UTC: " + UTC.dateTime());
|
||||
|
||||
Timezone myTZ;
|
||||
|
||||
// Provide official timezone names
|
||||
// https://en.wikipedia.org/wiki/List_of_tz_database_time_zones
|
||||
myTZ.setLocation(F("Pacific/Auckland"));
|
||||
Serial.print(F("New Zealand: "));
|
||||
Serial.println(myTZ.dateTime());
|
||||
|
||||
// Or country codes for countries that do not span multiple timezones
|
||||
myTZ.setLocation(F("de"));
|
||||
Serial.print(F("Germany: "));
|
||||
Serial.println(myTZ.dateTime());
|
||||
|
||||
// See if local time can be obtained (does not work in countries that span multiple timezones)
|
||||
Serial.print(F("Local (GeoIP): "));
|
||||
if (myTZ.setLocation()) {
|
||||
Serial.println(myTZ.dateTime());
|
||||
} else {
|
||||
Serial.println(errorString());
|
||||
}
|
||||
|
||||
Serial.println();
|
||||
Serial.println(F("Now ezTime will show an NTP sync every 60 seconds"));
|
||||
|
||||
// Set NTP polling interval to 60 seconds. Way too often, but good for demonstration purposes.
|
||||
setInterval(60);
|
||||
|
||||
// Make ezTime show us what it is doing
|
||||
setDebug(INFO);
|
||||
|
||||
}
|
||||
|
||||
void loop() {
|
||||
|
||||
events();
|
||||
|
||||
}
|
||||
Loading…
Reference in new issue